Відео

Thank you!!!!!!

Instructions were clearly delivered and also safety cannot be over emphasized.

That you sooo much !! We followed what you said to a T. My washer is now up and running again🎉❤😊

Thank You SOON Much,I just got my blazer and live in Minnesota So I Need 4wd a lot of the year,You showed me A Great deal of where my problem should be,Thank You SO Much!!!!!

12:11 listen closely

I installed these on my door. Guess it added too much pressure or something, the opener wouldnt lift the door enough or close appropriately. Had to uninstall. Maybe i need to move the tracks back a bit? Not sure. Just going to use weather stripping and insulate the garage door. Hopefully that helps prevent heat/cold loss from my garage gym.

No drain plug gasket?

Bullcrap

Where you have to put it

I cant get the plastic hub out of the transmission shaft. The opening of the hub is smaller than the shaft.

brown wire is grown and light green is backup light?

Jesus. Talk about making the job 10x harder than it needs to be.

I need to replace the plug on my pressure washer due to a broken prong. The current GFCI plug says "20A" on the back - can I cut off the plug and replace with a 15A plug similar to the one in your video, or will that cause a potential hazard/fire?

Very helpful, thanks!

Will the actuator be on the same place as? It was only Jimmy on a Chevrolet. S10 ZR2.

at the white wires the screw is burned and rusty it works with short cycles though any one knows the reason?

Gonna try it. So I don't need to worry about the tension spring if I am onloy removing the top section or second section from the top too?

terrible video. you talk too much. you do not stay on topic. you repeat yourself. garbage video

A Maine mechanic's trick is to cut the lines off flush with the fitting, and then use a socket.

Thank you for this informative video. I’m a single gal and have been having problems figuring out the cut off and cut on screw setting. Gonna go try. Thanks

Did you ever have to replace the Servi motor? Did you make a video? Can you share it if so? I'm curious if the new ones rest in a 'no resistance' state. That would be a better design IMHO since most people may leave it in the 0 or 1 state thereby always putting tension on the spring.

Thanks. Fixing to get into this job, thanks for the tips

My head hurts

So you need to pickle fork them out but don’t need to press them back in? Just torque to spec?

Oh just saved me $100s of dollars in future repairs.

I need help!! Chevy sliverado here that manually reclines forward or back and windows are manual as well. Seat is stuck forward and the lever isnt doing anything.

How do you get rid off the glue left behind... I keep using water and wiping down but takes forever. Is there a faster way? Thanks

My 2000 blazer won't engage. the light blinks and you can hear something engage but it doesn't actually engage

This works for any car?

After watching I have no doubt I can replace the joints on my ATV. Thanks for sharing.

Thank u sir, u just helped me fix my broken bowflex. Really appreciate you!!

Saved my day. It was stuck on one and I wanted 16. Did just as you said and voila it works perfectly now. Thanks!

If anyone is curious about the torque specification, the manual states it is 16 foot-pounds.

I never seen anything like it doesn't anyone work on the driver's side it's always the passenger side unreal..

this is the best video on this fix....

Works on a 2004 sportsman too Cutting down bolt was a difference maker. If you use a ratchet wrench, place it on that right hand bolt before you rotate into place and can use a long screwdriver to give a little pressure and seat that nut easily

Lmao watching this in 2024 you’re rocking Windows 7 in the background on the computer lmao. Thank you for the video. My LP I just picked up on Reverb has very deep slots on the nut and while I have the action set pretty good I feel like the strings are sitting a tad too low in the nut. It’s my understanding your strings more rest on the nut then they get forced *into* the nut. On my LP the strings are no joke in the nut

After 8 years, this is still the best video I could find on this job. Nice camera work and great explanation.

Hi... M8 BOWFLEX It's showing on the Update Required screen... I don't know how to solve it.

Is this fuse in the same location on the 2008 trailblazer?

Thanks so much1 I did this yesterday to my 2015 Cherokee. Used Mopar filter!

I’ve never done anything like this before, but my mini freezer ground plug broke off so I ordered this part and did what you said and it seems to be working!

Thank u. And is a midnight special edition

Dude, thank you for this tutorial, couldn’t have done it without it 👌🏻. Luckily didn’t had the bolt issue, got it out and in relatively easily. Thank you so much

Not well done

Thank you for the video! My M6 servo motor position was off the other direction causing the low resistance level to move the magnets off the brake disc entirely and the brake magnets keeps bouncing back (to look for some resistance I guess?). Now it's working properly. Thank you!

Does the negative cable have to be on the starter ? Mine didn’t have it on the starter (2002 Polaris Sportsman 400)

Great series 🙂 Very Helpful. I would have put some "Dielectric Grease" on the electrical connections, otherwise everything is perfect 🙂

2006hhr front

Thank you for sharing this 😊